EIGRP

EIGRP

ROUTER 1
Konfigurasi IP :
Router>enable
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.3.1 255.255.255.252
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#clock rate 64000
Router(config-if)#no sh
Router(config-if)#exit

Konfigurasi eigrp :
Router(config-if)#router eigrp 10
Router(config-router)#network 172.16.1.0 0.0.0.255
Router(config-router)#network 172.16.3.0 0.0.0.3
Router(config-router)#network 192.168.10.4 0.0.0.3

Konfigurasi Bandwidth :
Router(config)#int ser2/0
Router(config-if)#bandwidth 2048

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.3.2 (Serial2/0) is down: interface downRouter(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.3.2 (Serial2/0) is up: new adjacency
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#bandwidth 56

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.6 (Serial3/0) is down: interface downRouter(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.6 (Serial3/0) is up: new adjacency

ROUTER 2
Konfigurasi IP :
Router>enable
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.10.9 255.255.255.252
Router(config-if)#clock rate 64000
Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 172.16.3.2 255.255.255.252
Router(config-if)#clock rate 64000
Router(config-if)#no sh
Router(config-if)#exit

Konfigurasi eigrp :
Router(config)#router eigrp 10
Router(config-router)#network 192.168.2.0 0.0.0.255
Router(config-router)#network 192.168.10.8 0.0.0.3
Router(config-router)#network 172.16.3.0 0.0.0.3
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.3.1 (Serial3/0) is up: new adjacency

Konfigurasi bandwidth :
Router(config)#int ser2/0
Router(config-if)#bandwidth 2048

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.10 (Serial2/0) is down: interface downRouter(config-if)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.10 (Serial2/0) is up: new adjacency

ROUTER 3
Konfigurasi IP :
Router>enable
Router#config t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.10.6 255.255.255.252
Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.10 255.255.255.252
Router(config-if)#no sh
Router(config-router)#exit

Konfigurasi eigrp :
Router(config)#router eigrp 10
Router(config-router)#network 192.168.1.0 0.0.0.255
Router(config-router)#network 192.168.10.8 0.0.0.3
Router(config-router)#network 192.168.10.4 0.0.0.3

PC 1

PC 2

PC 3

ROUTER STATIS

ROUTER STATIS

Router 1 :

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.3.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config)#
Router(config)#
Router(config)#
Router(config)#conf t
%Invalid hex value
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 192.168.0.0 255.255.252.0 ser2/0
Router(config)#ip route 172.16.1.0 255.255.255.0 ser2/0
Router(config)#exit

Router 2 :

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
%LINK-5-CHANGED: Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 172.16.3.0 255.255.255.0 ser2/0
Router(config)#ip route 192.168.2.0 255.255.255.0 ser3/0

Router(config)#exit

Router 3 :

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#
Router(config)#ip route 172.16.0.0 255.255.252.0 ser2/0
Router(config)#

Konfigurasi PC

IP PC1 : 172.16.3.2 

SM       : 255.255.255.0

DG       : 172.16.3.1

IP PC2 : 172.16.1.2

SM       : 255.255.255.0

DG       : 172.16.1.1

IP PC3 : 192.168.2.2

SM       : 255.255.255.0

DG       : 192.168.2.1